Member Reviews for Cobra 4-1/2 in. Spotlight Visor (for bullet shaped spotlights) - Sold Each

All Cobra products are made in the USA

Write a review and share your experience with other members.

Average Customer Review: 4.37 (based on 75 reviews)

Breakdown:
4 Reviews
14 Reviews
1 Review

Sort By: Newest Oldest Highest Rated Lowest Rated Helpful Reviews

(4 stars) reviewed on 03/30/09 by Shrek (Shrek) from Sydney, , Asia, for a 2003 1300 VTX1300R (S) Retro wrote: Look great and make the spotlights match the headlamp better. Are well priced and solid. However they are a b*#!* to install as the wire circlips that hold the lens in place are very difficult to remove and then similar to install again without the lens moving. I have also noticed that the thickness of the visor causes the lens to sit back in the housing a little, this in turn will cause the lights to shine higher than originally set. As such, it is a simple matter to again adjust the spots to the correct alignment. I used a quality pair of long nosed pliers to remove/replace the clips. Oh and don't forget that you need to order two as they are sold individually! Review Details  1 out of 1 members found this review helpful. Was this review helpful to you? Yes No

(5 stars) reviewed on 01/18/09 by Scotty Gibbs (colonelg1990) from San Antonio, TX, United States, for a 2006 Candy Black Cherry 1300 VTX1300R (S) Retro wrote: I wanted these 4 1/2 visors to complete the look of my Cobra Lightbar and somewhat match the visor design of my 2006 Honda VTX 1300R. The visors are top notch and you will not regret buying a set to complete the retro look. Installation tip: You will have to remove 2 of the 3 retainer clips to get the visor in the housing. Once in the housing, replace the 2nd retainer clip. Then position the light and visor exactly where you want them and then install the 3rd retainer clip. I removed the light from the housing, pulled the wire through the retainer holes, and sat down in the floor to complete this task. You can easily re-thread the wire back through the holes when you are ready to install the light back into the housing. You will need needle nose pliers to grab one arm of the retainer clip, push it down, the pull it out to release the clip. I would recommend wearing safety glasses, as the clips are under a lot of tension and may fling towards your face if you lose your grip wi... Review Details  2 out of 2 members found this review helpful. Was this review helpful to you? Yes No

(3 stars) reviewed on 09/16/08 by (pinchemarc) from El Paso, TX, United States, for a 2006 1300 VTX1300R (S) Retro wrote: INSTALLATION INSTRUCTIONS TO INSTALL COBRA 4 1/2" SPOTLIGHT VISORS: 1] REMOVE SCREW FROM BOTTOM OF LIGHT 2] REMOVE LIGHT LENS FROM CHROME HOUSING 3] DISCONNECT ELECTRICAL CONNECTION 4] UTILIZING NEEDLE NOSE PLIERS REMOVE THE 3 SPRINGS HOLDING LIGHT LENS TO LIGHT LENS CHROME FRAME 5] INSTALL SPOTLIGHT AT TOP OF LIGHT LENS CHROME FRAME 6] PLACE LIGHT LENS BACK INTO LIGHT LENS CHROME FRAME WITH THE TOP SIDE UP 7] USING NEEDLE NOSE PLIERS, REPLACE THE 3 SPRINGS THAT HOLD THE LIGHT LENS TO THE LIGHT LENS FRAME 8] MAKE ELECTRICAL CONNECTION AND MOUNT LIGHT BACK ONTO LIGHT BAR 9] REPEAT FOR THE OTHER LIGHT....THESE VISOR LOOK AWESOME...THEY ARE NOT DIFFICULT TO INSTALL....THEY JUST TAKE A LITTLE BIT OF TIME. Review Details  Was this review helpful to you? Yes No

(5 stars) reviewed on 05/25/08 by Bill (scbambam) from Piedmont, SC, United States, for a 2003 Black with Gray Ghost Flames (Mom's Bike) 1300 VTX1300R (S) Retro wrote: More Chrome....really gives 'er that retro feal Review Details  1 out of 1 members found this review helpful. Was this review helpful to you? Yes No

(5 stars) reviewed on 09/24/07 by Chris Robison (crazyoldman) from Palm Harbor, FL, United States, for a 08 Triumph Rocket III Touring, Black, 2300cc 1300 VTX1300R (S) Retro wrote: easy to install in the lights. 15 minutes. Looks great ! Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 08/08/07 by (hwyblues) from Waxhaw, NC, United States, for a 2005 Silver 1300 VTX1300R (S) Retro wrote: Pain in the butt squeesing these in the houses. Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 06/01/07 by gene wilkins (gene1) from hellertown, PA, United States, for a 2005 1300 VTX1300R (S) Retro wrote: nice addition Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 04/06/07 by gene wilkins (redskin) from hellertown, PA, United States, for a 2005 1300 VTX1300R (S) Retro wrote: nice adds some detail Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 03/29/07 by Leroy Keith (Ridges) from , , for a 0 1300 VTX1300R (S) Retro wrote: Make sure you order 2, they don't come as a pair. Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 01/29/07 by kev (kevbur) from Sarnia, ON, Canada, for a 2006 Bright Blue Metallic 1300 VTX1300R (S) Retro wrote: Now the spots match the headlight Review Details  1 out of 2 members found this review helpful. Was this review helpful to you? Yes No

(4 stars) reviewed on 08/12/06 by Richard (rfaulconer) from Cocoa, FL, United States, for a 2005 1300 VTX1300R (S) Retro wrote: No-Brainer and the angle matches the stock headlight bucket fairly well. Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 03/20/06 by B Phil Howell (phildog) from Laurel Springs, NC, United States, for a 2004 1300 VTX1300R (S) Retro wrote: These look great!! ONE PROBLEM: TOOK OVER AN HOUR TO INSTALL!! I have absolutely no instructions to make them easier. Its a 10 minute job that is so damn hard it takes forever. The clipping system should be made different. The difference in appearance is definately worth it if you have the honda's with the egg'ish headlight!! Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 03/20/06 by B Phil Howell (phildog) from Laurel Springs, NC, United States, for a 2004 1300 VTX1300R (S) Retro wrote: These look great!! ONE PROBLEM: TOOK OVER AN HOUR TO INSTALL!! I have absolutely no instructions to make them easier. Its a 10 minute job that is so damn hard it takes forever. The clipping system should be made different. The difference in appearance is definately worth it if you have the honda's with the egg'ish headlight!! Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 10/12/05 by Michael McCracken (msm45069) from West Chester, OH, United States, for a 2005 silver 1300 VTX1300R (S) Retro wrote: A must have with the Cobra Light Bar. Very nice - though takes a little patience to install. Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 12/26/04 by Wite (WiteLiun) from South Yarmouth, MA, United States, for a 2004 1300 VTX1300R (S) Retro wrote: Someone once said ya needed 3 hands to install..yeah it takes a min ..If you have not looked into lights- 3 retainer clips hold light to frame. I removed 1 and slid part in. Worked well..present for Christmas Review Details  Was this review helpful to you? Yes No

(5 stars) reviewed on 10/27/04 by J.R. (hillbilly500) from crossville, TN, United States, for a 2003 1300 VTX1300R (S) Retro wrote: a little tough to install,not enough hands yet no room for them either. good quality,set off the look of the lights Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 07/03/04 by jwmoy (jwmoy) from Bonne Terre, MO, United States, for a 2003 1300 VTX1300R (S) Retro wrote: Mine is actually Honda brand. Just the two for the lightbar. {Honda Direct} Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 05/28/04 by joel McKinney (ezeorange) from Tracy, CA, United States, for a 2003-Peal Orange 1300 VTX1300R (S) Retro wrote: I have the Honda covers. Very nice complete the overall look to match the VTX headlight. Kind of a pain to install- get straight. Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 05/19/04 by john (yanni) from , ON, United States, for a 2004 1300 VTX1300R (S) Retro wrote: These complete the retro look of the headlight. Review Details  Was this review helpful to you? Yes No