Member Reviews for Electrical Connection Turn Signal Conversion Kit

CruiserCustomizing Staff Pick Important: SEE FITMENT DETAILS!


View installation guide

Write a review and share your experience with other members.

Average Customer Review: 4.46 (based on 840 reviews)

Breakdown:
20 Reviews
7 Reviews
1 Review

Sort By: Newest Oldest Highest Rated Lowest Rated Helpful Reviews

(4 stars) reviewed on 12/04/09 by dak (dakshack) from Oceanside, NY, United States, for a 2003 1600 Vulcan Classic wrote: lights up the back of the bike nicely great safety addition. However should have attached the led ring to the bulb instead of the clear lenses, would be a much "cleaner" appearance Review Details  Was this review helpful to you? Yes No

(5 stars) reviewed on 03/21/09 by ynkmup (ynkmup) from Florence, AL, US, for a 2007 1600 Vulcan Classic wrote: Great added saftey lights...looks great also. Take your time and have a bit of patience on istall and you will be pleased with outcome and looks. I liked them so well I took them off my other bike when I sold it and installed them on the Vulcan ! A+ for vehicles coming up on you. Review Details  1 out of 1 members found this review helpful. Was this review helpful to you? Yes No

(5 stars) reviewed on 04/17/08 by Jim Murdock (Cranium) from North Augusta, SC, United States, for a 2004 Black 1600 Vulcan Classic wrote: Used Gorilla Glue to mount into turnsignals vice the silicone they supply, really lights up the rear of the bike a lot more, I recommend this to all riders Review Details  1 out of 1 members found this review helpful. Was this review helpful to you? Yes No

(5 stars) reviewed on 03/10/07 by mark narloch (mnarloch) from Maineville, OH, United States, for a 2005 Burg/Beige 1600 Vulcan Classic wrote: These things work great!! The instructions were good especially the pictures and diagrams. It installed quite easily. If you remove the signal light housing from the bar that it attaches to it is quite easy to pull the the wires through. I used a stiff wire to hook the electric wires and pull them through. I also removed the tail light by unplugging the harness from under the fender. This made it easier to connect the new wires to the brake wires and then put them back through the tail light hole. Be sure you run the new wires through the hole from under the fender out to the tail light before you make your connections. Review Details  8 out of 8 members found this review helpful. Was this review helpful to you? Yes No

(4 stars) reviewed on 02/02/07 by Greg Joyce (gregjoyce) from Palm Bay, FL, United States, for a 2003 metallic black 1600 Vulcan Classic wrote: I'm very pleased with the light kit. The lights make me more visible at night as running lights and the brake lights will keep them awake and off my a... The kit comes with a tube of silicone that's supposed to hold the light ring to the inside of the lens. It didn't so I used super glue and they hold just fine. Review Details  4 out of 4 members found this review helpful. Was this review helpful to you? Yes No

(4 stars) reviewed on 08/04/06 by Bill Maxwell (maxwelwp) from LAKEVILLE, MN, United States, for a 2005 Beige 1600 Vulcan Classic wrote: Nice feature to help make your bike more visible. Not sure about the attachment method of the LED's (silicone to inside of lense). Time will tell. I expected these LED's to replace the original equipment but they are in addition to the the std bulbs. Took aout 3.5 hrs to install but I took the entire rear light harness out and routed wires for the LED's in the same bundle to a connection area under my seat. Much more professional install that way and keeps the connection drier. Functions as advertised. Review Details  8 out of 8 members found this review helpful. Was this review helpful to you? Yes No

(4 stars) reviewed on 07/16/06 by fireman (tlefire) from talladega, AL, United States, for a 2003 1600 Vulcan Classic wrote: Just put it on today. Seems to work very well. Review Details  0 out of 1 members found this review helpful. Was this review helpful to you? Yes No

(5 stars) reviewed on 06/20/06 by grumpy (grumpie) from PORT ST. LUCIE, FL, United States, for a 2006 red/blk 1600 Vulcan Classic wrote: Great product! Gives more attention to rear brake lights! Review Details  Was this review helpful to you? Yes No

(5 stars) reviewed on 06/19/06 by Gcar Caron (Gcar) from Galax, VA, United States, for a 2003 1600 Vulcan Classic wrote: Good Item. Helps to be seen. Review Details  1 out of 1 members found this review helpful. Was this review helpful to you? Yes No

(5 stars) reviewed on 06/13/06 by Mike Slapp (MSLAPP) from Middletown, NY, United States, for a 2005 Beige 1600 Vulcan Classic wrote: A very nice product. I had a problem with one of the LED's and the company sent out a replacement right away, and informed me that they warranty the LED's for life. Install was straight forward took about 2 hrs. You have to silicone the LED ring onto the inside of the lens. I did this the night before so I was able to install the next morning and go for a nice ride. Review Details  1 out of 1 members found this review helpful. Was this review helpful to you? Yes No

(5 stars) reviewed on 02/11/06 by Mike (VULCAN2) from Norton, OH, United States, for a 2005 1600 Vulcan Classic wrote: Just installed these, added alot of extra light in the back. Right where you need it. install was easy once you get through the fender. Don't use the supplied wire connectors. Do the job right. solder the wires it looks better and not as bulky under the seat. I have clear lenses so these are really bright at night when you need the light most. Review Details  Was this review helpful to you? Yes No

(5 stars) reviewed on 01/03/06 by Dion Cook (dionpcook) from Sacramento, CA, United States, for a Black 2005 1600 Vulcan Classic wrote: Greatly improves the amount of light in the back. The kit works exactly as advertised. I removed the turn signal bar - made install much easier. Soldered all connections just to make sure there would be no problems. Well worth the money. Review Details  1 out of 1 members found this review helpful. Was this review helpful to you? Yes No

(4 stars) reviewed on 08/13/05 by Darrell (dlee) from Temple, TX, United States, for a 2005 1600 Vulcan Classic wrote: I just put this on my bike. It was a bit of a job running the wires but other than that the instuctions were very detailed and helpful. I think it will add alot of awareness to the bikes rearend. Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 05/26/05 by Tom Richardson (tomrinbellingham) from Bellingham, WA, United States, for a 2003 1600 Vulcan Classic wrote: be safe be seen Review Details  Was this review helpful to you? Yes No

(5 stars) reviewed on 04/14/05 by Jeff Hinkel (JDHinkel) from Frisco, TX, United States, for a 2005 Black 1600 Vulcan Classic wrote: Really helps light the rear up. Not much different during daylight hours but at night a real difference. As Grandma would say, "How nice to see you?" Instructions are fairly simple. Was able to all of the installation under the rear fender of the bike. A small wire or "looped ear currette" (medical instrument) made it simple to get wiring through turn signal tube. I removed the harness from under the wheel well in order to connect all wire temporarily before cutting or soldering anything and tested the system out. Take your time and it will work. Review Details  3 out of 3 members found this review helpful. Was this review helpful to you? Yes No

(3 stars) reviewed on 04/09/05 by Lance Ganassi (sloflier) from , PA, United States, for a 1600 Vulcan Classic wrote: Just got this. Haven't had a chance to install yet. Review Details  0 out of 3 members found this review helpful. Was this review helpful to you? Yes No

(5 stars) reviewed on 04/06/05 by 2ter (Tuter) from Waterford, NY, United States, for a 2003 1600 Vulcan Classic wrote: The install isn't bad. Take off the turn signal assembly and the cover behind the fender, all the connections can be made right there with little difficulty. The instructions are good, just read and reread them and they will make sence. Many of the reviews I read said they didn't like the appearance of the LED's siliconed to the lenses, I siliconed them to the bulbs, just put a ring of silicone around the bulb, slide the LED ring on and let dry. I know, you will one day have to replace the bulbs, but it's only silicone, the LED's will come off. In the day light these new lights make little difference but at night they look great, they really stand out! Review Details  5 out of 5 members found this review helpful. Was this review helpful to you? Yes No

(5 stars) reviewed on 10/29/04 by Jeff Sodflyer Hargis (Sodflyer) from Cleveland, MO, United States, for a 2006 CLassic LT 1600 Vulcan Classic wrote: Much better for others to see me leaving Review Details  1 out of 1 members found this review helpful. Was this review helpful to you? Yes No

(5 stars) reviewed on 06/20/04 by DD (ddent01) from Sherrills Ford, NC, United States, for a 1600 Vulcan Classic wrote: Added seperate LED tail lights by my tag. Also added a Backoff type flasher for the brakelight. Review Details  0 out of 4 members found this review helpful. Was this review helpful to you? Yes No

(4 stars) reviewed on 06/16/04 by paul (pauhly) from brick, NJ, United States, for a 1600 Vulcan Classic wrote: saftey. should be stanard on bikes. Review Details  0 out of 2 members found this review helpful. Was this review helpful to you? Yes No