Member Reviews for Kuryakyn Round Shift Peg Cover (Each) - Various Kawasaki, Suzuki, Yamaha Cruiser Models

CruiserCustomizing Staff Pick Important: SEE FITMENT DETAILS!


View installation guide

Write a review and share your experience with other members.

Average Customer Review: 4.28 (based on 1466 reviews)

Breakdown:
23 Reviews
9 Reviews
3 Reviews

Sort By: Newest Oldest Highest Rated Lowest Rated Helpful Reviews

(5 stars) reviewed on 03/03/12 by Rod (RODERICK) from Chicago, IL, United States, for a 2004 1500 Intruder VL1500 LC wrote: LOOKS GREAT Review Details  Was this review helpful to you? Yes No

(5 stars) reviewed on 03/18/10 by Roadcaptain (roadcaptain) from Copenhagen, , Denmark, for a 2009 Black 1500 Intruder VL1500 LC wrote: Looks great Review Details  Was this review helpful to you? Yes No

(5 stars) reviewed on 10/04/08 by Ken Thomas (frozentexn) from Broomfield, CO, United States, for a 2003, Black 1500 Intruder VL1500 LC wrote: Adds a little extra. I went to the Lowes and picked up a piece of rubber hose to slip the peg over. Between the rubber hose and glue this sucker is not coming off. Review Details  Was this review helpful to you? Yes No

(5 stars) reviewed on 05/15/08 by Mooner (snyder78) from Lexington, TN, United States, for a 2001 1500 Intruder VL1500 LC wrote: GREAT LOOK!! Review Details  2 out of 2 members found this review helpful. Was this review helpful to you? Yes No

(5 stars) reviewed on 05/07/08 by DAN SCHMIDT (DANIELJR) from Colorado Springs, CO, for a 2001 1500 Intruder VL1500 LC wrote: Had to cut the old one off, wrap the bare peg with electrical tape and applied a lot of glue. Review Details  1 out of 1 members found this review helpful. Was this review helpful to you? Yes No

(5 stars) reviewed on 01/02/08 by Arnell O'Neil (arnello) from Chicago, IL, United States, for a 2002 1500 Intruder VL1500 LC wrote: Easy to install, looks good. Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 12/17/07 by Diz Disney (diz5) from douglasville, GA, United States, for a 2000 1500 Intruder VL1500 LC wrote: Nice ad-on. Had to glue it on, lost the first one. Worth the trouble tho. Review Details  1 out of 1 members found this review helpful. Was this review helpful to you? Yes No

(5 stars) reviewed on 10/29/07 by Derrick Pendergrass (pendergrass_d) from Chattanooga, TN, United States, for a 2000-black 1500 Intruder VL1500 LC wrote: Love it! Looks great. Review Details  Was this review helpful to you? Yes No

(5 stars) reviewed on 10/25/07 by phillip (phantomphill) from Thornton NSW, , Asia, for a 12/1997 metalic purple 1500 Intruder VL1500 LC wrote: nice peice Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 07/24/07 by Tim (phaedo68) from Huntington, WV, United States, for a 2001 1500 Intruder VL1500 LC wrote: Installed in minutes. I was able to slide the OEM rubber cover off without any cutting. More than a few layers of electrical tape, some Gorilla Glue, overnight for the glue to dry and it's ready to roll. Looks great. Feels great. It's a super inexpensive part, but it really adds the overall look of the bike, especially if you have other Kuryakyn parts installed. Review Details  Was this review helpful to you? Yes No

(5 stars) reviewed on 05/14/07 by Andrew Herrington (twistedmetal) from Kitchener, ON, for a 2002 custom paint, lots of chrome 1500 Intruder VL1500 LC wrote: Again, great Kuryakyn product, good finish and looks. When installing use electrical tape as per instructions provided, however I found it is important to use more tape at the end of the shifter where you are more likely to place your foot. This will keep the peg on a more level plain since this is the point that you will be applying the most pressure. Allen screw is extremely small so be careful not to over torque this product. Review Details  Was this review helpful to you? Yes No

(5 stars) reviewed on 02/05/07 by Sam Haines (smule) from tracy, CA, United States, for a silver and gold 04 1500 Intruder VL1500 LC wrote: again a little something different Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 10/22/06 by Ken (kblue) from Yuma, AZ, United States, for a 2004 1500 Intruder VL1500 LC wrote: Used duct tape after Removing OME then used some jb kwick weld. dont over tightened allen set screw. Looks good goes with hand Grips and heel shaft cover. Review Details  Was this review helpful to you? Yes No

(5 stars) reviewed on 08/24/06 by Bill Mertens (Donk) from Tannersville, PA, United States, for a 2003 1500 Intruder VL1500 LC wrote: It was a little bit of work to get it to fit just right, however I love the lool Review Details  Was this review helpful to you? Yes No

(5 stars) reviewed on 06/28/06 by Blaise Stegman (blaiser15) from , AR, United States, for a 2004 1500 Intruder VL1500 LC wrote: easy to install <5 minutes, looks great. Review Details  Was this review helpful to you? Yes No

(3 stars) reviewed on 05/01/06 by Jeff Tolar (Bodean) from columbia, MS, United States, for a 1999 1500 Intruder VL1500 LC wrote: Cool piece. I had to build up the shifter to keep it from turning. I did this with a piese of tubbing. Review Details  1 out of 1 members found this review helpful. Was this review helpful to you? Yes No

(5 stars) reviewed on 04/23/06 by Shawn Damon (manateern) from Alamogordo, NM, United States, for a 2004 Pearl White/Silver 1500 Intruder VL1500 LC wrote: Matches my Grips. Better looking than stock. Review Details  1 out of 1 members found this review helpful. Was this review helpful to you? Yes No

(3 stars) reviewed on 04/16/06 by Gene West (sick055) from Des Moines, IA, United States, for a 2003 1500 Intruder VL1500 LC wrote: I have one of these on my bike and my wifes bike. They are hard to keep tight and they spin around alittle. Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 02/10/06 by tony (aspruil) from greenville, SC, United States, for a 2001, Black 1500 Intruder VL1500 LC wrote: Looks good Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 01/17/06 by Drew (drewtay) from Toccoa, GA, United States, for a 2002 vs800glp 1500 Intruder VL1500 LC wrote: Looks nice. Review Details  Was this review helpful to you? Yes No