Member Reviews for Kuryakyn Universal Wiring and Relay Kit For Use With Kuryakyn Halogen Silver Bullets

CruiserCustomizing Staff Pick Important: SEE FITMENT DETAILS!


View installation guide

Write a review and share your experience with other members.

Average Customer Review: 4.14 (based on 177 reviews)

Breakdown:
3 Reviews
3 Reviews
1 Review

Sort By: Newest Oldest Highest Rated Lowest Rated Helpful Reviews

(5 stars) reviewed on 01/18/09 by Toney (cbchemist) from Vicksburg, MS, United States, for a 2007 Silver 1100 Shadow Spirit wrote: made installing light bar very easy Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 08/06/08 by DAVID (trckkenworth) from , , for a 0 1100 Shadow Spirit wrote: MADE WIRING UP MY LIGHT BAR A SNAP Review Details  0 out of 1 members found this review helpful. Was this review helpful to you? Yes No

(5 stars) reviewed on 09/09/06 by pondnut (pondnut) from Grundy Center, IA, United States, for a 2004 1100 Shadow Spirit wrote: Nice wiring kit. I would have given excellent across the board, but knocked a point on ease of install for not including a schematic. The text description does a good job of IDing the wires for you but a schematic would have been easier to read IMHO. Update: Set aside three hours for install if you want to do a professional grade job. Dont rush it, cut wires to the correct length as you go along. Because this is desgned as a universal kit the wires are probably longer than you'll need. Have a soldering iron, electrical solder, and some heat shrink handy for customizing the wires to your bike. (I dont like quick connects or crimp connects normally). Along with the tools to remove the seat and tank. A Clymer service manual helps for identifing wires too. I removed the switch from the kit and wired the relay to the wire that comes from the start switch. (The wire that feeds the High/Low beam switch.) This way the bullet lights come on when the regular lights do, as well as turn ... Review Details  10 out of 10 members found this review helpful. Was this review helpful to you? Yes No

(3 stars) reviewed on 03/28/06 by Killer Bee (Kevin5133) from Reinholds, PA, United States, for a 1997 Yellow & Black Spirit 1100 Shadow Spirit wrote: I thought this would be the easiest way to go so I didn't have to figure too much out. I used this with a pair of 50w Vizor lights on a pair of Kuryakyn P clamps as driving lights. The only thing I didn't like was where I had to mount the switch because of the pre determined length of the wires. The switch is also not esily attached anywhere, just a black box with a rocker switch and wires out the back. Review Details  1 out of 1 members found this review helpful. Was this review helpful to you? Yes No

(5 stars) reviewed on 01/19/06 by John (JAMuir) from Grant, MI, United States, for a 2005 1100 Shadow Spirit wrote: A must when wiring Aux lighting. It just makes life simple. Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 10/11/05 by James (JRobin) from WSMR, NM, United States, for a 2005 1100 Shadow Spirit wrote: Used with my light bar. Relay mounts great under the seat next to an existing relay. Review Details  Was this review helpful to you? Yes No

(4 stars) reviewed on 05/12/04 by Mongoose39 (mongoose39) from Edmonton, AB, Canada, for a 1100 Shadow Spirit wrote: A must have for the Kuryakyn LED light bar set. UPDATE June 1, 2004 - I did most the wiring for this under the seat. I attached the relay and all the black grounds to a convenient bolt. I traced the wires back from the ignition switch to under the seat also. You have to slice open the black casing in order to access the constant power and the switched power from the ignition switch. I used a 12 volt Automotive tester to see which wire was which. I then tapped into the appropriate wire using the provided connectors. I ran the lightbar power wires back under the gas tank on the right hand side following the hoses that are existing. I had to add more wire to the lightbar power wires in order to get them under the seat. Grounding the lightbar is unecessary as this is done through the chassis. There are actually 2 black ground wires in the harness that are not needed because of this. I located the switch on the right hand side sticking out from under the seat...I am not happy with this loca... Review Details  2 out of 2 members found this review helpful. Was this review helpful to you? Yes No